Jan 29, 2013 Going beyond the typical LS tuning software, JET Performance is now expanding their tuning software with the all new D.S.T. It allows complete control of just about every single aspect of your vehicle's computer including top speed and engine rev limiters. Read all about it here. As the Exclusive Australasian Distributor of HP Tuners VCM Suite tuning software, VCM Suite Australasia Pty Ltd is proud to offer the most advanced, most comprehensive tuning software currently available for performance tuning of all LS powered vehicles (all USA and 1999 to current Commodore). HP’s software.
[Editor’s Note:This LS3 engine upgrade guide is the second in a series of LS engine upgrade guides assembled by a team of LS experts at Summit Racing. The LS3 engine is a Gen IV, 6.2L aluminum-block V8 car engine that first appeared in the 2008 Chevrolet Corvette. The L99—introduced for the 2010 Chevy Camaro SS—is also a Gen IV 6.2L aluminum-block V8, but with the addition of Active Fuel Management and Variable Valve Timing. Below you’ll see references to the L99 as a result. For a primer on the LS engine universe, read LS Engines 101: An Introductory Overview of the Gen III/IV LS Engine Family.]
…
May 01, 2008 This LS1 was fitted with a FAST dual wideband O2 system, and utilized scan tool/data logging software to keep track of the air/fuel ratio and spark timing of each tuner. See all 3 photos. With just a mild cam and valvespring swap, a diminutive Gen III 5.3L LS can make north of 400 hp. Add pocket-ported LS heads and GM's superior TrailBlazer SS intake manifold,.
Intro to LS3 Upgrades
On a stock LS3 engine, the following upgrades can improve performance and fuel economy:
- A cold air intake kit
- An aftermarket exhaust system
- A computer programmer
[Every engine spec you’ll need for an LS3 project can be found here:LS3 Engine Specs: Performance, Bore & Stroke, Cylinder Heads, Cam Specs & More.]
The LS3 and L99 are both Gen IV, 6.2L, aluminum block, car engines which came under the hoods of GM performance cars between 2008 and 2017. Both the LS3 and L99 engine blocks can be pushed to 850 to 1,000 horsepower.
Both engines use rectangle port cylinder heads and have a common 4.065-inch bore diameter. They also have the internal oil passages for Active Fuel Management (AFM), even if unused.
It is common for owners of GM performance vehicles with AFM-equipped LS or LS-based Vortec engines to delete or disable the cylinder-deactivation feature to maximize engine power.
For more on that, read: How to Delete or Disable Active Fuel Management (AFM) on GM Engines.
How to Tell the Difference Between LS3 and L99
1983 xlx 1000 service manual. At first glance, these engines look very similar. The easiest way to tell them apart is to check the 8th digit of the VIN code.
If you don’t have the VIN, you will need to look much closer. The major differences between these engines is the special technology used in the cylinder heads which you can learn more about here.
If you have an LS3 and are on the hunt for the best mods, you’re in the right place. Here’s the roadmap to upgrading your LS3 powerplant to achieve maximum performance.
…
(Summit Racing’s Paul Spurlock contributed to this article.) Dark souls pc settings crash.
…
Upgrading the LS3 Intake Manifold and Throttle Body
(Image/LSX Magazine)
The rectangle port intakes flow well, but an aftermarket intake can still make more power. Sage act pro 2012 keygen.
Shorter runner intake manifolds and single-plane intakes make more top-end power, but can lose just as much low-end torque. Make sure the intended power band matches your gear ratio and torque converter.
At 90mm, the factory 4-bolt throttle body is fairly large and won’t be a restriction in most applications. Most aftermarket intakes are designed to accommodate larger 102mm throttle bodies.
…
[Trying to find an LS engine for a swap or build? Check out Part 1 and Part 2 of our LS Spotter’s Guide.]
…
Upgrading the LS3 Camshaft and Valvetrain
LS engines respond well to cam swaps.
In addition to valve springs and rockers, the cam needs to match the compression, torque converter, rear-end gears, etc. How to hd youtube videos mac.
Be careful on an LS3. Piston-to-valve clearance is very tight with cams over 230-degree duration @ 0.050 inch.
Spring kits are available for typical 0.600 in. lift cam upgrades. Titanium retainers are another upgrade that will reduce valve float.
The trunnion bearings in the stock rocker arms are another known weak point.
A trunnion upgrade kit should be installed when you upgrade the valvetrain.
Upgrading to full roller rockers is another option.
The stock rockers are pedestal mounted. High spring pressure (over 475 pounds) can pull the bolts out of the cylinder head. Converting to roller rockers and stud mounts is recommended for cams over 0.600-inch lift.
…
Upgrading the LS3 Fuel System and Tuning the Engine
(Image/YouTube-Watch Me Wrench)
Upgrading to larger fuel injectors is often needed to meet the demand of increased power.
The factory fuel pump will become a limitation around 575 hp. So, plan on upgrading the fuel pump as well.
Tuning the computer changes the fuel and ignition curves to increase performance. Plug-in programmers are easy to use, but limited. Custom tuning requires more knowledge, but will provide even better performance.
…
Adding an LS3 Supercharger or Nitrous Oxide System
Many supercharger kits are bolt-on and work with stock internals and pump gas. More serious kits are available, but will require internal upgrades.
Nitrous kits are also available, inexpensive, and easy to install. Street kits have lower settings that work with stock internals. More power requires higher settings and upgrading the engine internals.
… Office for mac jailbreak.
Upgrading LS3 Cylinder Heads
(Image/LS1Tech)
Best Ls1 Tuning Software Reviews
The L99 and LS3 heads have rectangle intake ports.
The lighter hollow stem valves used in the LS3can be installed in L99 heads to increase the rpm range. It is also common to CNC port and/or mill them up to 0.030 inch to increase compression and better airflow.
There are many aftermarket cylinder heads available. The heads flow better and have thicker decks to maintain head gasket seal. A wide range of runner and chamber volumes are available. Some also go from a 15-degree to a 13.5-degree valve angle for even more power.
A 4-corner steam kit is another smart upgrade. It reduces hot spots in cylinder #7 that can cause the piston rings to butt and crack the piston.
Ls1 Tuning Guide
… Favilla guitar serial numbers.
Upgrading the LS3 Rotating Assembly
The stock pistons are a known weak point.
They will crack in high-horsepower engines. A set of forged pistons should be high on your priority list.
When stroking, choose a piston with minimal skirt taper. This prevents the piston from rocking at BDC and scraping up the skirts.
Gen 4 rods are stronger than the Gen 3’s and have full floating pins. They can handle about 800 hp and 6,500 rpm in boosted applications. If you’re getting forged pistons, upgrade to forged connecting rods at the same time.
Even though it’s cast, the crankshaft can handle about 900 hp and 7,000 rpm (for a limited time). A broken crankshaft is bad news. Upgrading to a forged crankshaft early in your build will save you the headache later. When you upgrade, a crankshaft with a longer stroke costs about the same and increases displacement.
The chart below lists standard specs compared to common performance rotating assemblies.
Standard vs. Performance Specs for LS3 Rotating Assemblies
Gen IV LS Standard Spec | Stroke | Rod Length / Wristpin | Bore Size / Compression Distance |
LS3 | 3.622 in. | 6.098 in. / 0.9431 in. | 4.065 in. / 1.338 in. |
Common Stroker Combinations | Stroke | Rod Length / Wristpin | Bore Size / Compression Distance |
6.2L to 6.8L | 4.000 in. | 6.125 in. / 0.927 in. | 4.070 in. / 1.110 in. |
6.2L to 7.0L | 4.100 in. | 6.125 in. / 0.927 in. | 4.070 in. / 1.050 in. |
6.2L to 7.0L | 4.125 in. | 6.125 in. / 0.927 in. | 4.070 in. / 1.050 in. |
…
Upgrading the LS3 Engine Block
(Image/LS1Tech)
LS3 engines (as well as the L99) have a 4.065-inch bore diameter.
The cylinders can be bored to 4.080 inch. However, we recommended leaving them as thick as possible when running boost. When bored and stroked, displacement can be as high as 427 c.i.d. (7.0 L).
The block can handle 850 to 1000 horsepower. However, you will want to upgrade to head studs and main studs if you plan on using boost or nitrous.
…
(Information for this article originally appeared in thisUpgrading the Gen. 4, 6.2L, LS Car Enginesarticle atSummit Racing’s searchable database of FAQ tech info. Go there and search “LS engines” for a comprehensive collection of LS engine tech information.)
…
NOTE: You can find engine specs and detailed engine upgrade advice for every LS and LS-based Vortec truck engine in one place: The Definitive Guide to LS Engine Specs and LS Engine Upgrades.